Item No. REH-014
Not every hose can run in a straight line. Engine bays, machine enclosures, and vehicle frames are full of obstacles that force piping to turn, drop, or double back at short notice. Elbow hoses are made for exactly those situations — routing fluid and air around a corner without introducing a joint, a fitting, or a leak point.
Each hose is built from high-grade heat-resistant rubber and shaped with a 90-degree or custom-angled bend during production. The result is a single continuous part that turns smoothly, maintains full flow through the bend, and keeps its seal through temperature swings, pressure changes, and constant vibration. Used across cooling systems, intake and exhaust lines, and fuel circuits, these hoses deliver the same reliable performance whether installed in a passenger car, a piece of industrial equipment, or a commercial vehicle.
Built-in bend – 90-degree standard, with 45°, 135°, and custom angles available
Heat-resistant rubber construction – silicone, EPDM, NBR, and other compounds
Reinforced wall options – polyester or aramid fabric for pressure resistance
Smooth bore through the bend – maintains flow without restriction or turbulence
Leak-free connections – designed for secure sealing at both ends
Flexible in tight spaces – routes around obstacles without kinking or collapsing
Temperature stable – performs across a wide range depending on compound
Chemical resistance – grade-dependent resistance to coolants, oils, and fuels
Aging and weather resistant – resists UV, ozone, and oxidation over time
Custom manufacturing – bend angle, leg length, diameter, and color to order
Turns Without a Joint – The bend is molded into the hose itself, eliminating the extra fittings, clamps, and potential leak points that a straight hose plus elbow would require.
Keeps Flow Smooth Through the Bend – The internal bore follows the curve without collapsing or restricting, so pressure drop and turbulence stay low.
Fits Where Straight Hose Cannot – Designed to route around engines, frames, and equipment housings in spaces too tight for a straight run.
Handles Heat, Pressure, and Vibration – Heat-resistant compounds and reinforced walls maintain performance under the combined stresses of engine bays and industrial equipment.
Automotive cooling systems – radiator hoses, heater hoses, bypass lines
Turbo and intake systems – charge air connections, air intake routing
Exhaust and EGR circuits – high-temperature gas routing
Fuel and oil lines – directional changes in engine and hydraulic systems
Industrial machinery – equipment cooling, pneumatic lines, process piping
Materials
EPDM, Viton
Hardness
35-80ShA
Logo
Custom
Application
Engine Air Supply, Crankshaft & Camshaft, Engine Cooling System
Standard: Goods are typically supplied in about 20-25kg/carton.
Standardized Pallets: Goods are stacked on heat-treated (ISPM 15) or plastic pallets, optimized for forklift handling. Rigid Corner Protectors: High-impact cardboard corner guards are applied to the full height of the stack. This prevents the straps from cutting into the rubber and maintains the vertical integrity of the pallet.
What bend angles can you produce?
90 degrees is standard. We also produce 45°, 135°, and fully custom angles to match your routing requirements.
How do I specify leg length?
Measure the straight distance from the connection point to the start of the bend on each leg. Send us a drawing or sample and we will match it.
What materials are available?
Silicone, EPDM, NBR, neoprene, and custom compounds, with polyester or aramid reinforcement options.
Can the hose handle high temperatures?
Silicone grades perform up to +230°C. EPDM and NBR handle lower ranges. Tell us your operating temperature and we will recommend a compound.
Is the bend reinforced?
Yes. Reinforcement extends through the bend to prevent collapse under pressure and vacuum.
Can these hoses be used with fuel and oil?
NBR compounds offer good fuel and oil resistance. Silicone is not recommended for prolonged petroleum exposure.
Do you offer food-grade elbow hoses?
Yes. FDA-compliant silicone and EPDM compounds are available for food and beverage applications.
Can you produce custom diameters and colors?
Yes. Any inner diameter, wall thickness, and color can be produced to your specification.
If you have any questions or needs about the product, please fill in the following form and we wll contact you as soon as possible.
PHONE: +86 0532 8769 9025
EMAIL: sales@todorubber.com
Located in Jimo
Located in Xinhe
